乐动体育app买球-首页

山东创图建筑装饰工程有限公司 山东创图建筑装饰工程有限公司
加工技术热线:18660816658 网站地图
  • 您当前位置: 首页>>新闻动态>>行业动态>>抗倍特使用时要知道的八个注意事项

    行业动态

    抗倍特使用时要知道的八个注意事项

    来源:/ 日期:2022-07-04 发布人:fumeijia
    抗倍特被广泛用于学校实验室、医院等,那么在使用抗倍特时应该注意哪些问题?下面小编为您整理总结了八点,一起来看看。
    Anti beta is widely used in schools, laboratories, hospitals, etc., so what should be paid attention to when using anti beta? The following editor summarizes eight points for you. Let's have a look.
    1、抗倍特应存放在阴凉干燥场地,避免阳光直射和直接放在地面上,避免受潮。存放条件是18-25℃,相对湿度45-55%,存储时间不超过6个月。
    1. Kangbeite should be stored in a cool and dry place, away from direct sunlight and directly on the ground to avoid moisture. The storage condition is 18-25 ℃, relative humidity 45-55%, and the storage time shall not exceed 6 months.
    2、抗倍特加工前一定要清除工作台面的异物,以避免板材在拖拉、裁切时造成划伤,不能使用尖锐物品刮拭保护膜表面。
    2. Before anti Beite processing, the foreign matters on the worktable must be removed to avoid scratches caused by dragging and cutting the plate. Sharp objects cannot be used to wipe the surface of the protective film.
    3、抗倍特裁切时需沿长度方向裁切,以保证板材拼接时的同向拼接。
    3. It needs to be cut along the length direction when cutting anti Beite, so as to ensure the same direction splicing when splicing plates.
    4、抗倍特抗倍特在裁切加工时,如果有双面保护膜的必须将双面保护膜同时保留或者同时撕去,以保证产品两面受环境因素的影响程度一致。如仅仅保留单面保护膜,则一定要用PVC类薄膜对板材以及半成品加以包裹。
    4. When cutting, if there is a double-sided protective film, the double-sided protective film must be kept or torn off at the same time to ensure that both sides of the product are affected by environmental factors. If only one-sided protective film is retained, the sheet and semi-finished products must be wrapped with PVC film.
    富美家抗倍特
    5、抗倍特保证堆放整齐,尺寸小的板材叠于尺寸大的上面,以维持受力的均衡,台面做好假厚以后,堆放时中间放置适当同样厚度的边条垫实,避免板材受力不均匀。
    5. Kangbeite ensures that the plates with small size are stacked neatly on the plates with large size, so as to maintain the balance of stress. After the false thickness of the table is made, the edge strips with the same thickness are placed in the middle of stacking to avoid uneven stress of the plates.
    6、抗倍特成品和半成品在包装或存放时,底部和顶部分别使用垫板和盖板,以隔绝潮湿空气对上下板子单面的影响,防止产生翘曲。
    6. When anti Beite finished products and semi-finished products are packed or stored, base plates and cover plates are used at the bottom and top respectively to isolate the influence of moist air on one side of the upper and lower plates and prevent warpage.
    7、抗倍特使用于实验室台面的安装时,必须使用螺丝固定法,同时每间隔80cm使用直角五金固定,并采用直径5mm左右的平头螺丝固定直角五金,钻孔采用带限的枪钻,以防止钻孔深度过大,穿透表面。到工地后应尽快安装,安装结束后应立刻撕去耐火板表面的保护膜,否则在长时间下容易产生受力不均而变形。
    7. When anti Beite is used for the installation of the laboratory table, it must use the screw fixation method. At the same time, it must use the right angle hardware to fix every 80cm, and use the flat head screws with a diameter of about 5mm to fix the right angle hardware. The limited gun drill is used for drilling to prevent the drilling depth from being too large and penetrating the surface. After arriving at the construction site, it should be installed as soon as possible. After installation, the protective film on the surface of the refractory board should be immediately removed, otherwise it is easy to produce uneven stress and deformation for a long time.
    8、富美家抗倍特在取用时,一定要两人以上同时抬取,避免在产品表面的拖动和碰撞,防止表面划伤和边角破损。
    8. When taking fumeijia kangbeite, two or more people must lift it at the same time to avoid dragging and collision on the surface of the product and prevent surface scratches and corner damage.
    以上就是问题解答的相关内容了,希望能够帮助到大家,如对这一问题还存在任何疑问,都欢迎关注我们网站并咨询我们的工作人员,将竭诚为您服务。
    The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website And consult our staff, will serve you wholeheartedly.
    联系我们

    产品销售热线:18660816658

    技术方案咨询:18560211715

    仓库地址:济南市槐荫区河海工业园9号

    九江工厂:九江市江东大道3号

    台湾新竹工厂:台湾新竹

    泰国曼谷工厂:泰国曼谷

    关注我们
    山东创图建筑装饰工程有限公司 备案号:鲁ICP备14019259号-2 网站地图 xml txt 技术支持:网站建设·推广运营流量统计

    截屏,微信识别二维码

    微信号:18660816658

    Baidu
    sogou