乐动体育app买球-首页

山东创图建筑装饰工程有限公司 山东创图建筑装饰工程有限公司
加工技术热线:18660816658 网站地图
  • 您当前位置: 首页>>新闻动态>>行业动态>>富美家A级墙板边缘加工操作时的九点事项

    行业动态

    富美家A级墙板边缘加工操作时的九点事项

    来源:/ 日期:2022-06-20 发布人:fumeijia
    1、切割材料时应以直线锯切为主。通常,您可以先在板上画出规格和尺寸,然后再看到。如果工件尺寸是标准尺寸,可以在锯前用模板划线,方便很多。
    1. Linear sawing shall be the main method for cutting materials. Usually, you can draw the specifications and dimensions on the board before you see them. If the workpiece size is a standard size, you can use a template to draw lines before sawing, which is much more convenient.
    2、开孔时,可用便携式曲线锯切割。切割速度为3-4m/min。如果切割速度过快,一方面会使刃口出现爆裂等缺陷,另一方面也会影响锯片的使用。寿命,增加不必要的加工成本。
    2. Portable curve saw can be used to cut holes. The cutting speed is 3-4m/min. If the cutting speed is too fast, on the one hand, the cutting edge will burst and other defects, on the other hand, it will also affect the use of the saw blade. Life, increase unnecessary processing costs.
    3、富美家A级墙板加工时,应先在板面画出所需尺寸,再用曲线锯切割;如果大批量生产,可以使用大型CNC进行切割,这样可以保证加工速度和锯切质量。
    3. During the processing of Formica class a wall panels, the required dimensions shall be drawn on the panel surface first, and then cut with a curve saw; In case of mass production, large CNC can be used for cutting, which can ensure the processing speed and sawing quality.
    4、边缘加工操作前应清板面的灰尘或异物,以免在板面留下划痕或划痕。路由器的加工速度应保持在2m/min。如果铣刀的刃角小,工件的厚度较厚,则应适当放慢铣刀的加工速度。
    4. Before edge processing, the dust or foreign matters on the plate surface shall be removed to avoid scratches or scratches on the plate surface. The processing speed of the router shall be kept at 2m/min. If the edge angle of the milling cutter is small and the thickness of the workpiece is thick, the processing speed of the milling cutter should be appropriately slowed down.
    另外,铣刀刃口的长度应大于工件的厚度,以保证一次走刀就能铣出刃口的线形。通过时,刳刨机应从高位逐渐下滑至较低位置,直至刳刨机刃盖住铣刃。值得注意的是,刀一定要保持稳定,不要让路由器晃动。晃动会使工件边缘产生不规则的波纹,增加后续打磨抛光工序的工作量,影响加工效率。
    In addition, the length of the cutting edge of the milling cutter shall be greater than the thickness of the workpiece to ensure that the linear shape of the cutting edge can be milled out at one time. When passing, the planer shall gradually slide down from the high position to the low position until the planer edge covers the milling edge. It is worth noting that the knife must remain stable and do not let the router shake. Shaking will cause irregular ripples at the edge of the workpiece, increase the workload of the subsequent grinding and polishing process, and affect the processing efficiency.
    富美家A级墙板
    5、打磨时,用80#、220#、320#砂纸依次打磨边缘。打磨速度以15-20分钟2.5米长度为准;打磨时应注意不要损坏表面装饰层。用抛光剂抛光边缘。抛光剂可以使用人造大理石的抛光蜡,抛光程序如下:
    5. When polishing, polish the edges with 80\220\320\. The grinding speed shall be subject to the length of 2.5m within 15-20 minutes; Be careful not to damage the surface decorative layer during grinding. Polish the edges with polish. The polishing agent can use the polishing wax of artificial marble, and the polishing procedure is as follows:
    用柔软的棉布蘸取适量的抛光蜡,擦拭边缘;
    Dip a proper amount of polishing wax with a soft cotton cloth and wipe the edge;
    抛光蜡干后,在边缘涂上一层抛光蜡,用布擦拭,使其有光泽,后涂上一层抛光蜡,用干净的布擦拭,直到边缘光亮。
    After the polishing wax is dry, apply a layer of polishing wax on the edge and wipe it with a cloth to make it shiny. Then apply a layer of polishing wax and wipe it with a clean cloth until the edge is bright.
    6、富美家A级墙板拼板时应掌握以下几点:
    6. The following points shall be mastered when Formica class a wallboard is assembled:
    胶粘剂的涂布量应控制在2.5-3.0g/cm2,粘合面应充分涂布;
    The coating amount of adhesive shall be controlled within 2.5-3.0g/cm2, and the bonding surface shall be fully coated;
    拼接后,用夹子夹住约30分钟。垂直方向粘接时,必须打开开口,增加粘接面,保证粘接强度;
    After splicing, clamp for about 30 minutes. When bonding vertically, the opening must be opened to increase the bonding surface to ensure the bonding strength;
    一旦发现待粘接的零件有裂纹等缺陷,应将光滑平整的一面朝外,以保证粘接质量。
    Once cracks and other defects are found on the parts to be bonded, the smooth and flat side shall face outward to ensure the bonding quality.
    7、如果要使用螺钉连接产品,应先用比螺钉直径小的钻头钻一个小孔,然后在小孔内注入粘合剂,然后拧入螺钉,并确保螺纹上缘旋入5mm以上。
    7. If screws are used to connect products, drill a small hole with a drill bit smaller than the screw diameter, then inject adhesive into the small hole, then screw in the screws, and ensure that the upper edge of the thread is screwed in more than 5mm.
    8、钻杯形隐链孔时,板的剩余厚度应保持至少3mm。如果剩余厚度太薄,嵌入后会损坏杯形铰链或出现凸痕。安装暗链时,孔底和固定螺丝孔要涂上粘合剂,然后用螺丝拧紧。螺钉不要拧得过紧,否则板边会突出,严重时会折断。
    8. When the cup-shaped hidden chain hole is drilled, the remaining thickness of the plate shall be kept at least 3mm. If the remaining thickness is too thin, the cup hinge will be damaged or convex marks will appear after insertion. When installing the concealed chain, the bottom of the hole and the fixing screw hole shall be coated with adhesive, and then tightened with screws. Do not over tighten the screws, otherwise the plate edge will protrude and break in serious cases.
    9、如果安装结束时富美家A级墙板表面有斑点或污渍,可以用毛巾沾上少量油性清洁剂(油和丙酮的混合物)轻轻擦拭这些斑点或去除污渍。如果没有斑点或污迹,请使用肥皂和水等一般清洁剂或清洁剂和水擦拭。
    9. If there are spots or stains on the surface of Formica class a wallboard at the end of installation, gently wipe these spots or stains with a towel dipped with a small amount of oily detergent (a mixture of oil and acetone). If there are no spots or stains, wipe with general detergent such as soap and water or detergent and water.
    以上就是今天为大家分享的关于问题的相关内容,希望对大家能有所帮助,想要了解更多内容可以电话联系我们或者关注我们的网站。
    The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website 。
    联系我们

    产品销售热线:18660816658

    技术方案咨询:18560211715

    仓库地址:济南市槐荫区河海工业园9号

    九江工厂:九江市江东大道3号

    台湾新竹工厂:台湾新竹

    泰国曼谷工厂:泰国曼谷

    关注我们
    山东创图建筑装饰工程有限公司 备案号:鲁ICP备14019259号-2 网站地图 xml txt 技术支持:网站建设·推广运营流量统计

    截屏,微信识别二维码

    微信号:18660816658

    Baidu
    sogou