乐动体育app买球-首页

山东创图建筑装饰工程有限公司 山东创图建筑装饰工程有限公司
加工技术热线:18660816658 网站地图
  • 您当前位置: 首页>>新闻动态>>公司新闻>>质地坚硬的抗倍特怎么顺利的处理

    公司新闻

    质地坚硬的抗倍特怎么顺利的处理

    来源:/ 日期:2022-12-23 发布人:fumeijia
    由于抗倍特板材的质地很坚硬,因此在加工时应注意一些方面与细节点,下面富美家抗倍特厂家为您解说。
    Due to the hard texture of the laminate, attention should be paid to some aspects and fine nodes during processing. Now, the manufacturer of Fumeijia Anti PET will explain it to you.
    1.开料时,应以直线锯切为主。通常可先在这种板材上画好规格尺寸,然后再锯切,如果工件的尺寸为标准尺寸,可先用模板划线,再进行锯切,这会方便得多。
    1. When cutting, it shall be mainly linear sawing. Generally, the specification and size can be drawn on this kind of plate before sawing. If the size of the workpiece is standard, the template can be used to draw a line before sawing, which will be much more convenient.
    2.开孔时,可利用手提曲线锯进行切割,切割速度以3-4m/min为宜,如切割速度过快,一方面会使切割边缘产生爆口等缺陷,另一方面也会影响锯条的使用寿命,增加加工成本。
    2. When making holes, the hand-held curve saw can be used for cutting. The cutting speed should be 3-4m/min. If the cutting speed is too fast, on the one hand, it will cause defects such as cracks at the cutting edge, on the other hand, it will also affect the service life of the saw blade and increase the processing cost.
    3.加工异形边沿时,应先在板件表面划出所需尺寸,然后利用曲线锯切割;如果批量生产时,可利用模板进行切割,这样可确保加工速度和锯切质量。
    3. When processing the irregular edge, the required size shall be marked on the surface of the plate first, and then the curve saw shall be used for cutting; In case of mass production, the template can be used for cutting to ensure the processing speed and sawing quality.
    富美家抗倍特
    4.加工边缘时,普遍采用的工具是手提镂铣机,在作业前,应清除板件表面的灰尘或异物,以免在抗倍特板件表面留下划痕或刻痕。
    4. When processing edges, the commonly used tool is a hand-held router. Before operation, the dust or foreign matters on the surface of the plate should be removed to avoid scratches or nicks on the surface of the anti magnification plate.
    5.砂磨时,按顺序分别采用80#、220#和320#砂纸对边缘进行砂磨,打磨速度以15-20分钟打磨2.5米长度为基准;打磨时,应注意不要损坏表面装饰层,打磨结束后,用抛光剂对边缘进行抛光处理。
    5. During sanding, the edges shall be sanded with 80 #, 220 # and 320 # sandpaper in order, and the sanding speed shall be based on the length of 2.5 meters polished in 15-20 minutes; During polishing, be careful not to damage the surface decorative layer. After polishing, polish the edges with polishing agent.
    6.板件拼接时,应掌握以下几点:a.粘合剂的涂布量应控制在2.5-3.0g/cm2;粘接表面要全部涂布到;b.拼接后,用夹子夹紧30分钟左右。竖直方向粘合时,一定要开口,使粘合面增大,以确保粘合强度;c.一旦发现被粘合部件有爆口等缺陷,应将光滑平整的一面朝外,以保证粘合质量。
    6. During panel splicing, the following points shall be mastered: a. The coating amount of adhesive shall be controlled within 2.5-3.0g/cm2; The bonding surface shall be completely coated; b. After splicing, clamp for about 30 minutes. When bonding in the vertical direction, be sure to open to increase the bonding surface to ensure the bonding strength; c. Once it is found that the bonded parts have defects such as bursting, the smooth and flat side shall be outward to ensure the bonding quality.
    7.如要利用螺钉连接产品,应先用比螺钉直径小的钻头钻一个小孔,然后向小孔注入粘合剂,再把螺钉拧入,并保证螺钉牙纹的上沿部分拧入5mm以上。
    7. If you want to use screws to connect products, first drill a small hole with a drill bit smaller than the screw diameter, then inject adhesive into the hole, and then screw the screw in, and ensure that the upper edge of the screw thread is screwed in more than 5mm.
    8.钻杯状暗较链孔肘,板件的剩余厚度至少保留3mm以上,如剩余厚度过薄,杯状绞链埋入后,会发生破损或出现凸痕。装暗较链时,孔底和固定螺丝孔内应涂上粘合剂,然后再用螺钉拧紧,紧固螺钉时,不要过度,否则也会使板件边缘部分外凸,严重时,会将其顶破。
    8. Drill cup shaped concealed chain hole elbow, and the remaining thickness of the plate shall be at least 3 mm. If the remaining thickness is too thin, the cup shaped hinge will be damaged or convex after being embedded. When installing the concealed chain, the hole bottom and the fixing screw hole should be coated with adhesive, and then the screws should be tightened. When tightening the screws, do not excessive, otherwise the edge of the panel will also be convex, and in serious cases, it will be broken.
    质地坚硬的抗倍特怎么顺利的处理?我们从以上八个操作方面了解起来,您有什么疑惑或者需求可以随时来我们网站进行咨询!
    How can the hard Kangbeite be handled smoothly? We understand from the above eight operations that you can come to our website at any time if you have any doubts or needs Consult!
    联系我们

    产品销售热线:18660816658

    技术方案咨询:18560211715

    仓库地址:济南市槐荫区河海工业园9号

    九江工厂:九江市江东大道3号

    台湾新竹工厂:台湾新竹

    泰国曼谷工厂:泰国曼谷

    关注我们
    山东创图建筑装饰工程有限公司 备案号:鲁ICP备14019259号-2 网站地图 xml txt 技术支持:网站建设·推广运营流量统计

    截屏,微信识别二维码

    微信号:18660816658

    Baidu
    sogou