乐动体育app买球-首页

山东创图建筑装饰工程有限公司 山东创图建筑装饰工程有限公司
加工技术热线:18660816658 网站地图
  • 您当前位置: 首页>>新闻动态>>常见问题>>使用抗倍特板时注意八点事项

    常见问题

    使用抗倍特板时注意八点事项

    来源:/ 日期:2022-10-10 发布人:fumeijia
    抗倍特板材作为高密度的人造板材,质地很坚硬。因此富美家抗倍特板厂家认为,在使用的抗倍特板时应注意以下几个方面:
    As a high density artificial board, the quality of the anti Beite board is very hard. Therefore, the manufacturer of Fumeijia MP special plate believes that the following aspects should be paid attention to when using MP special plate:
    1.开料时,需要以直线锯切为主。通常可先在抗倍特板材上画好规格尺寸,然后再锯切。如果工件的尺寸为标准尺寸,可先用模板划线后再进行锯切,这样会更加方便。
    1. Straight sawing is the main method for cutting. In general, the specifications and dimensions can be drawn on the special resistance plate before sawing. If the size of the workpiece is the standard size, the template can be used for scribing before sawing, which will be more convenient.
    2.开孔时,可以使用手提曲线锯进行切割,切割速度控制在3-4m/min为宜。如果切割速度过快,一方面可能会造成切割边缘爆口等缺陷,另一方面也可能会影响锯条的使用寿命,增加加工的成本。
    2. When opening holes, the portable curve saw can be used for cutting, and the cutting speed should be controlled at 3-4m/min. If the cutting speed is too fast, on the one hand, it may cause defects such as cutting edge bursting, on the other hand, it may also affect the service life of the saw blade and increase the processing cost.
    3.对异形边沿进行加工时,需要先在板件表面划出所需尺寸,然后使用曲线锯切割;如果是批量生产,可以在模板的辅助下进行切割,这样可同时确保加工速度和锯切质量。
    3. When processing the irregular edge, it is necessary to draw the required size on the surface of the plate first, and then use a curve saw to cut; In case of batch production, cutting can be carried out with the aid of the template, which can ensure the processing speed and sawing quality at the same time.
    4.加工边缘,通常采用的工具是手提镂铣机。加工之前需要清除板件表面的灰尘或异物,以免在板件表面留下划痕或刻痕。另外镂铣机的加工速度应保持在2m/min为宜。如果镂铣刀刀刃角度较小而工件厚度又较厚时,镂铣机的加工速度应适当放慢。
    4. Handheld router is usually used to process edges. Before processing, it is necessary to remove the dust or foreign matters on the surface of the panel to avoid leaving scratches or nicks on the surface of the panel. In addition, the processing speed of the router should be kept at 2m/min. If the cutting edge angle of the router is small and the workpiece thickness is thick, the processing speed of the router should be appropriately slowed down.
    5.砂磨时,按顺序分别采用80#、220#和320#砂纸对边缘进行砂磨。打磨速度以2.5米/15-20分钟为基准。打磨时,应注意不要损坏表面装饰层。打磨结束后,用抛光剂对边缘进行抛光处理。
    5. During sanding, the edges shall be sanded with 80 #, 220 # and 320 # sandpaper in sequence. The grinding speed is based on 2.5m/15-20min. When grinding, be careful not to damage the surface decorative layer. After polishing, polish the edges with polishing agent.
    富美家抗倍特
    6.拼接板件时,应注意粘合剂的涂布量需要控制在2.5-3.0g/cm2,并且要确保涂布到全部粘接表面;拼接后,用夹子压合30分钟左右。竖直方向粘合时,一定要开口,增大粘合面,以确保粘合的强度;一旦发现被粘合部件有爆口等缺陷,需要将光滑平整的一面朝外,以保证粘合的质量。
    6. When splicing plates, it should be noted that the amount of adhesive coating should be controlled within 2.5-3.0g/cm2, and it should be ensured that all bonding surfaces are coated; After splicing, press with clips for about 30 minutes. When bonding in the vertical direction, be sure to open and increase the bonding surface to ensure the bonding strength; Once it is found that the bonded parts have defects such as bursting, the smooth and flat side needs to be outward to ensure the quality of bonding.
    7.如果是利用螺钉连接产品的,需要先用比螺钉直径小的钻头钻一个小孔,然后向小孔注入粘合剂。后把螺钉拧入,并确保螺钉牙纹的上沿部分拧入5mm以上。
    7. If the product is connected by screws, it is necessary to drill a small hole with a drill bit smaller than the screw diameter, and then inject adhesive into the hole. Then screw in the screw and ensure that the upper edge of the screw thread is screwed in more than 5mm.
    8.在钻杯状暗铰链孔时,板件的剩余厚度应该保留在3mm以上。如剩余厚度过薄,杯状铰链埋入后,会产生破损或出现凸痕。装暗铰链时,孔底和固定螺丝孔内应涂上粘合剂,然后再用螺钉拧紧。紧固螺钉时,不要过度,否则也会使板件边缘部分外凸,严重时会将其顶破。
    8. When drilling cup shaped concealed hinge holes, the remaining thickness of the plate should be kept above 3mm. If the remaining thickness is too thin, the cup-shaped hinge will be damaged or have bumps after being embedded. When installing the concealed hinge, the bottom of the hole and the inside of the fixing screw hole should be coated with adhesive, and then tightened with screws. Do not tighten the screws too much, otherwise the edge of the panel will bulge, and it will burst in severe cases.
    抗倍特板在安装结束时,如果表面出现斑点或污迹,可用毛巾沾取少量油性清洁剂(油与丙酮的混合物)轻轻擦拭去这些斑点或污点。如果没有斑点或污迹,用一般清洁剂如肥皂加水,或洗洁精加水擦拭即可。更多相关事项就来我们网站咨询吧!
    At the end of the installation of the anti magnification special plate, if there are spots or stains on the surface, use a small amount of oily cleaner (mixture of oil and acetone) dipped in a towel to gently wipe away these spots or stains. If there is no spot or stain, wipe it with general detergent such as soap and water, or detergent and water. Come to our website for more information Consult!
    联系我们

    产品销售热线:18660816658

    技术方案咨询:18560211715

    仓库地址:济南市槐荫区河海工业园9号

    九江工厂:九江市江东大道3号

    台湾新竹工厂:台湾新竹

    泰国曼谷工厂:泰国曼谷

    关注我们
    山东创图建筑装饰工程有限公司 备案号:鲁ICP备14019259号-2 网站地图 xml txt 技术支持:网站建设·推广运营流量统计

    截屏,微信识别二维码

    微信号:18660816658

    Baidu
    sogou